For hundreds of years, the game of pool has existed in many forms. Despite the fact that there have been significant changes to materials comprising certain aspects of the game, the element that has been most consistent is the felt cover. The bad news is that the lifespan of felt covers is not always as long as that of the table itself. When it comes to pool table refelting Denver residents ought to know the basics.
Some of the needed materials for the exercise are felts, socket wrench, felt, cleanser, rag, hammer and a staple gun among others. To begin with, the staples that surround the pockets at the underside of the table are removed. There is then removal of the nails that secure the rails to the underside using a socket wrench. On an approximate basis, one needs to look for three bolts for each rail.
After all the bolts have been removed, the rails will need to be taken off. This will be followed by detaching of the pocket liners. The staples that attach the felt to rail cushions will have to be pulled out. Felt covering the cushions will then need to be removed, after which it gets removed from the table top. At this stage, one has to determine if the felt gets glued or stapled, or both. The staples that are hold the felt are removed using a staple puller. Removal of the glued felt is supposed to be done very gently.
It will be then time to prepare the slate for re-felting. Pool table wax is used for filling in all holes and cracks. After letting the wax harden for one minute, the excess gets scrapped off using a putty knife. A gentle cleanser is then used for cleaning the surface of the slate. Before getting covered with the felt, the surface has to be left to dry completely.
The felt pieces that are being used will need to be measured. This will ensure that they are cut in accordance to the dimensions of the table. Edges of the felt are aligned flush with the table edges. As a matter of fact, the measurements should be very accurately done so that it fits well to the table.
After making the measurements and doing the cutting, the fabric will need to be stapled to the table. This is started from the center of any short edge and moving gradually towards the corners. During all this, the pockets ought not to be covered. During placement of the staples, the person doing the work should move in increments of roughly two inches as the fabric is pulled taut. This happens for all table sides.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
The rails are then wrapped with felt. The unique design of the rails is observed to know how large the felt piece has to be. There is then reattaching the rails to the table. Finally, the pockets and liners will be replaced as necessary.
Some of the needed materials for the exercise are felts, socket wrench, felt, cleanser, rag, hammer and a staple gun among others. To begin with, the staples that surround the pockets at the underside of the table are removed. There is then removal of the nails that secure the rails to the underside using a socket wrench. On an approximate basis, one needs to look for three bolts for each rail.
After all the bolts have been removed, the rails will need to be taken off. This will be followed by detaching of the pocket liners. The staples that attach the felt to rail cushions will have to be pulled out. Felt covering the cushions will then need to be removed, after which it gets removed from the table top. At this stage, one has to determine if the felt gets glued or stapled, or both. The staples that are hold the felt are removed using a staple puller. Removal of the glued felt is supposed to be done very gently.
It will be then time to prepare the slate for re-felting. Pool table wax is used for filling in all holes and cracks. After letting the wax harden for one minute, the excess gets scrapped off using a putty knife. A gentle cleanser is then used for cleaning the surface of the slate. Before getting covered with the felt, the surface has to be left to dry completely.
The felt pieces that are being used will need to be measured. This will ensure that they are cut in accordance to the dimensions of the table. Edges of the felt are aligned flush with the table edges. As a matter of fact, the measurements should be very accurately done so that it fits well to the table.
After making the measurements and doing the cutting, the fabric will need to be stapled to the table. This is started from the center of any short edge and moving gradually towards the corners. During all this, the pockets ought not to be covered. During placement of the staples, the person doing the work should move in increments of roughly two inches as the fabric is pulled taut. This happens for all table sides.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
The rails are then wrapped with felt. The unique design of the rails is observed to know how large the felt piece has to be. There is then reattaching the rails to the table. Finally, the pockets and liners will be replaced as necessary.
About the Author:
Find a review of the advantages of hiring a provider of pool table refelting Denver services and more information about a reliable service provider at http://www.anytimebilliards.com now.
Aucun commentaire:
Enregistrer un commentaire